nach oben

Lasers in Manufacturing and Materials Processing

Erschienen in:

25.04.2024 | Research

Co-based and Co/WC Laser Metal Deposition: A Comparative Study between Continuous and Pulsed Wave Laser Process Conditions

verfasst von: Haideé Ruiz-Luna, Cinthia Estefania Cuevas-Mercado, Christian Félix-Martínez, Juan Manuel González-Carmona, Juan Ruiz-Ornelas, Juan Manuel Alvarado-Orozco

Erschienen in: Lasers in Manufacturing and Materials Processing | Ausgabe 2/2024

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Laser metal deposition (LMD) has attracted global interest due to its capacity to fabricate wear-resistant materials. However, the magnitude of heat input is crucial during the manufacturing of hard-facing alloys. This study explores the potential of LMD to deposit Co/WC composite coatings using different laser beam emission modes—specifically, continuous and pulsed waves. Co-based coatings without WC were also fabricated for comparative analysis. The primary characteristics of the coatings, including macro- and microstructural evaluations, chemical and phase composition, hardness, and wear resistance, were systematically studied and compared to laser emission type, track overlapping percentage, and laser delay time. Results indicate the homogeneous distribution of hard WC particles along the coatings, regardless of the process parameters. A notable finding is the fine-grained microstructure developed when employing a pulsed-wave laser condition, further enhanced with increased delay time. The pulsed-wave mode inhibits the dissolution of WC particles, whereas secondary carbides are formed in the coatings under continuous-wave mode. The hardness of Co/WC composite coatings is 1.2 to 1.5 times higher than that of Co coatings. Partial WC dissolution positively influences the wear rate of composite coatings, reducing its value by 1.9 to 3.7 times.

Vorheriger Artikel Effect of Process Parameters on Bend Angle during Underwater Laser Bending of SS304 Sheet

Nächster Artikel Influence of Polymer Surface Roughness on the Fractions of Transmitted, Reflected and Absorbed Energy in Operation of Laser Transmission Welding

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Hasan, M.S., Mazid, A.M., Clegg, R.: The basics of stellites in machining perspective. Int. J. Eng. Mater. Manuf. 1, 35–50 (2016). https://doi.org/10.26776/IJEMM.01.02.2016.01CrossRef

Pauzi, A.A., Husin, S.: Study on the effect of wear resistant materials applications in reducing wear damage of gas turbine combustor components. Appl. Mech. Mater. 575, 17–21 (2014). https://doi.org/10.4028/WWW.SCIENTIFIC.NET/AMM.575.17CrossRef

Foster, J., Cullen, C., Fitzpatrick, S., Payne, G., Hall, L., Marashi, J.: Remanufacture of hot forging tools and dies using laser metal deposition with powder and a hard-facing alloy stellite 21®. J. Remanufacturing. 9, 189–203 (2019). https://doi.org/10.1007/S13243-018-0063-9CrossRef

Davis, J.R.: Nickel, Cobalt, and their alloys. ASM Int. Mater. Park OH (2000)

Bartkowski, D., Bartkowska, A.: Wear resistance in the soil of Stellite-6/WC coatings produced using laser cladding method. Int. J. Refract. Met. Hard Mater. 64, 20–26 (2017). https://doi.org/10.1016/j.ijrmhm.2016.12.013CrossRef

Lian, G., Yao, M., Liu, Z., Yang, S., Chen, C., Wang, H., Xiang, Y., Cong, W.: Near-net shaping control of triangular stacking in laser cladding process. Procedia Manuf. 34, 233–238 (2019). https://doi.org/10.1016/J.PROMFG.2019.06.144CrossRef

Li, W., Xu, P., Wang, Y., Zou, Y., Gong, H., Lu, F.: Laser synthesis and microstructure of micro- and nano-structured WC reinforced co-based cladding layers on titanium alloy. J. Alloys Compd. 749, 10–22 (2018). https://doi.org/10.1016/J.JALLCOM.2018.03.235CrossRef

Moradi, M., Ashoori, A., Hasani, A.: Additive manufacturing of stellite 6 superalloy by direct laser metal deposition – part 1: Effects of laser power and focal plane position. Opt. Laser Technol. 131, 106328 (2020). https://doi.org/10.1016/j.optlastec.2020.106328

Zieliński, A., Smoleńska, H., Serbiński, W., Kończewicz, W., Klimpel, A.: Characterization of the co-base layers obtained by laser cladding technique. J. Mater. Process. Technol. 164–165, 958–963 (2005). https://doi.org/10.1016/J.JMATPROTEC.2005.02.093CrossRef

10.

Díaz, E., Amado, J.M., Montero, J., Tobar, M.J., Yáñez, A.: Comparative study of co-based alloys in repairing low cr-mo steel components by laser cladding. Phys. Procedia. 39, 368–375 (2012). https://doi.org/10.1016/J.PHPRO.2012.10.050CrossRef

11.

Toyserkani, E., Khajepor, A., Corbin, S.: Laser Cladding. CRC Press LLC, USA (2005)

12.

Morrow, W.R., Qi, H., Kim, I., Mazumder, J., Skerlos, S.J.: Environmental aspects of laser-based and conventional tool and die manufacturing. J. Clean. Prod. 15, 932–943 (2007). https://doi.org/10.1016/J.JCLEPRO.2005.11.030CrossRef

13.

Dev Singh, D., Arjula, S., Raji Reddy, A.: Functionally graded materials manufactured by direct energy deposition: A review. Mater. Today Proc. 47, 2450–2456 (2021). https://doi.org/10.1016/J.MATPR.2021.04.536

14.

Ghosal, P., Majumder, M.C., Chattopadhyay, A.: Study on direct laser metal deposition. Mater. Today Proc. 5, 12509–12518 (2018). https://doi.org/10.1016/J.MATPR.2018.02.232

15.

Amado, J.M., Tobar, M.J., Alvarez, J.C., Lamas, J., Yánez, A.: Laser cladding of tungsten carbides (Spherotene®) hardfacing alloys for the mining and mineral industry. Appl. Surf. Sci. 255, 5553–5556 (2009). https://doi.org/10.1016/J.APSUSC.2008.07.198CrossRef

16.

Shah, K., Pinkerton, A.J., Salman, A., Li, L.: Effects of melt pool variables and process parameters in laser direct metal deposition of aerospace alloys. Mater. Manuf. Process. 25, 1372–1380 (2010). https://doi.org/10.1080/10426914.2010.480999CrossRef

17.

Wu, T., Shi, W., Xie, L., Gong, M., Huang, J., Xie, Y., He, K.: Effect of preheating temperature on geometry and mechanical properties of laser cladding-based stellite 6/wc coating. Materials. 15, 3952 (2022). https://doi.org/10.3390/ma15113952CrossRef

18.

Ahmed, N.: Direct metal fabrication in rapid prototyping: A review. J. Manuf. Process. 42, 167–191 (2019). https://doi.org/10.1016/j.jmapro.2019.05.001CrossRef

19.

Moradi, M., Hasani, A., Malekshahi Beiranvand, Z., Ashoori, A.: Additive manufacturing of stellite 6 superalloy by direct laser metal deposition – part 2: Effects of scanning pattern and laser power reduction in differrent layers. Opt. Laser Technol. 131, 106455 (2020). https://doi.org/10.1016/J.OPTLASTEC.2020.106455CrossRef

20.

Zhang, H., Zou, Y., Zou, Z., Zhao, W.: Comparative study on continuous and pulsed wave fiber laser cladding in-situ titanium-vanadium carbides reinforced Fe-based composite layer. Mater. Lett. 139, 255–257 (2015). https://doi.org/10.1016/j.matlet.2014.10.102CrossRef

21.

Wang, G., Zhang, J., Shu, R., Yang, S.: High temperature wear resistance and thermal fatigue behavior of Stellite-6/WC coatings produced by laser cladding with co-coated WC powder. Int. J. Refract. Met. Hard Mater. 81, 63–70 (2019). https://doi.org/10.1016/j.ijrmhm.2019.02.024CrossRef

22.

Li, B., Jin, Y., Yao, J., Li, Z., Zhang, Q.: Solid-state fabrication of WCp-reinforced Stellite-6 composite coatings with supersonic laser deposition. Surf. Coat. Technol. 321, 386–396 (2017). https://doi.org/10.1016/j.surfcoat.2017.04.062CrossRef

23.

Thawari, N., Chandak, G.C., Gupta, A.: Influence of laser cladding parameters on distortion, thermal history and melt pool behaviour in multi-layer deposition of stellite 6: In-situ measurement. J. Alloys Compd. 860, 157894 (2021). https://doi.org/10.1016/J.JALLCOM.2020.157894CrossRef

24.

Ostolaza, M., Zabala, A., Arrizubieta, J.I., Llavori, I., Otegi, N., Lamikiz, A.: High-temperature tribological performance of functionally graded Stellite 6/WC metal matrix composite coatings manufactured by laser-directed energy deposition. Friction. 12, 522–538 (2024). https://doi.org/10.1007/S40544-023-0790-2/METRICSCrossRef

25.

Bartkowski, D., Kinal, G.: Microstructure and wear resistance of Stellite-6/WC MMC coatings produced by laser cladding using yb:YAG disk laser. Int. J. Refract. Met. Hard Mater. 58, 157–164 (2016). https://doi.org/10.1016/j.ijrmhm.2016.04.017CrossRef

26.

Sun, S., Durandet, Y., Brandt, M.: Parametric investigation of pulsed nd: YAG laser cladding of stellite 6 on stainless steel. Surf. Coat. Technol. 194, 225–231 (2005). https://doi.org/10.1016/J.SURFCOAT.2004.03.058CrossRef

27.

Wang, X., Zhang, Z., Zhao, Y., Hu, Z., Li, X.: Macroscopic morphology and properties of cobalt-based laser cladding layers on rail steel based on pulse shaping. Opt. Laser Technol. 168, 109940 (2024). https://doi.org/10.1016/J.OPTLASTEC.2023.109940CrossRef

28.

Sun, S., Durandet, Y., Brandt, M.: Melt pool temperature and its effect on clad formation in pulsed nd:Yttrium-aluminum-garnet laser cladding of stellite 6. J. Laser Appl. 19, 32–40 (2007). https://doi.org/10.2351/1.2402524CrossRef

29.

Sun, S., Brandt, M.: Comparison between continuous wave and pulsed Nd:YAG laser cladding of stellite 6. ICALEO 2004–23rd Int Congr Appl Laser Electro-Optics, Congr. Proc. (2004). https://doi.org/10.2351/1.5060303/1002632

30.

Cuevas-Mercado, C.E.: Fabricación De recubrimientos de aleación base Co Y Co/WC mediante la técnica de deposición de Metal por Laser (in Spanish). Autonomous University of Zacatecas (2023)

31.

E384 Standard Test Method for Microindentation Hardness of Materials. Accessed 15 Feb 2023. https://www.astm.org/e0384-17.html

32.

G99 Standard Test Method for Wear Testing with a Pin: -on-Disk Apparatus. https://www.astm.org/g0099-17.html. Accessed 10 Jul 2023

33.

Easterling, K.E.: Introduction to the Physical Metallurgy of Welding, 2nd edn. Butterworth Heinemann Ltd (1992)

34.

Ganesh, P., Moitra, A., Tiwari, P., Sathyanarayanan, S., Kumar, H., Rai, S.K., Kaul, R., Paul, C.P., Prasad, R.C., Kukreja, L.M.: Fracture behavior of laser-clad joint of Stellite 21 on AISI 316L stainless steel. Mater. Sci. Eng. A. 527, 3748–3756 (2010). https://doi.org/10.1016/J.MSEA.2010.03.017CrossRef

35.

Hemmati, I., Ocelík, V., De Hosson, J.T.M.: Dilution effects in laser cladding of Ni–Cr–B–Si–C hardfacing alloys. Mater. Lett. 84, 69–72 (2012). https://doi.org/10.1016/j.matlet.2012.06.054CrossRef

36.

Zanzarin, S., Bengtsson, S., Molinari, A.: Study of dilution in laser cladding of a carbon steel substrate with Co alloy powders. Powder Metall. 59, 85–94 (2016). https://doi.org/10.1080/00325899.2015.1118842CrossRef

37.

Vilar, R.: Laser cladding. J. Laser Appl. 11, 64–79 (1999). https://doi.org/10.2351/1.521888CrossRef

38.

Pacheco, J.T., da Silva, L.J., Barbetta, L.D., Santos Ferreira, H., Taveira Veiga, M., Forni, R., Teixeira, M.F.: Laser cladding of stellite-6 on AISI 316 L austenitic stainless steel: Empirical-statistical modeling and parameter optimization. Lasers Manuf. Mater. Process. 8, 1–14 (2021). https://doi.org/10.1007/S40516-020-00132-0/METRICSCrossRef

39.

Gan, Z., Yu, G., He, X., Li, S.: Numerical simulation of thermal behavior and multicomponent mass transfer in direct laser deposition of co-base alloy on steel. Int. J. Heat. Mass. Transf. 104, 28–38 (2017). https://doi.org/10.1016/J.IJHEATMASSTRANSFER.2016.08.049CrossRef

40.

Kurz, W., Bezençon, C., Gäumann, M.: Columnar to equiaxed transition in solidification processing. Sci. Technol. Adv. Mater. 2, 185–191 (2001). https://doi.org/10.1016/S1468-6996(01)00047-XCrossRef

41.

Xiao, H., Li, S., Han, X., Mazumder, J., Song, L.: Laves phase control of Inconel 718 alloy using quasi-continuous-wave laser additive manufacturing. Mater. Des. 122, 330–339 (2017). https://doi.org/10.1016/j.matdes.2017.03.004CrossRef

42.

Li, S., Xiao, H., Liu, K., Xiao, W., Li, Y., Han, X., Mazumder, J., Song, L.: Melt-pool motion, temperature variation and dendritic morphology of Inconel 718 during pulsed- and continuous-wave laser additive manufacturing: A comparative study. Mater. Des. 119, 351–360 (2017). https://doi.org/10.1016/j.matdes.2017.01.065CrossRef

43.

Kazymyrovych, V., Kryzhanivskyy, V.: Thermal properties of cemented carbides used for metal cutting. Int. J. Refract. Met. Hard Mater. 111, 106097 (2023). https://doi.org/10.1016/j.ijrmhm.2022.106097CrossRef

44.

Zhou, Y., Wen, S., Wang, C., Duan, L., Wei, Q., Shi, Y.: Effect of TiC content on the Al-15Si alloy processed by selective laser melting: Microstructure and mechanical properties. Opt. Laser Technol. 120, 105719 (2019). https://doi.org/10.1016/j.optlastec.2019.105719CrossRef

45.

De Lovelock, V.: Powder/Processing/Structure relationships in WC-Co thermal spray coatings: A review of the published literature. J. Therm. Spray. Technol. 7, 357–373 (1998). https://doi.org/10.1361/105996398770350846CrossRef

46.

Zanzarin, S., Bengtsson, S., Molinari, A.: Study of carbide dissolution into the matrix during laser cladding of carbon steel plate with tungsten carbides-stellite powders. J. Laser Appl. 27, S29209 (2015). https://doi.org/10.2351/1.4906480CrossRef

47.

Sassatelli, P., Bolelli, G., Lassinantti Gualtieri, M., Heinonen, E., Honkanen, M., Lusvarghi, L., Manfredini, T., Rigon, R., Vippola, M.: Properties of HVOF-sprayed Stellite-6 coatings. Surf. Coat. Technol. 338, 45–62 (2018). https://doi.org/10.1016/J.SURFCOAT.2018.01.078CrossRef

48.

Ates, S., Aslan, O., Tümer, M., Arisoy, C.F.: Impact sliding wear behavior of stellite 6 and stellite 12 hardfacings. Mater. Chem. Phys. 313, 128762 (2024). https://doi.org/10.1016/J.MATCHEMPHYS.2023.128762CrossRef

49.

Wang, R., Ye, S., Cheng, P., Xie, Z., Wang, Y., Zhang, Y., Li, G., Wu, W., Lu, X.: Microstructure and wear resistance of in-situ TiC reinforced Stellite 6 coating using PTA cladding. J. Mater. Res. Technol. 27, 2656–2669 (2023). https://doi.org/10.1016/J.JMRT.2023.10.053CrossRef

50.

Navas, C., Conde, A., Cadenas, M., De Damborenea, J.: Tribological properties of laser clad stellite 6 coatings on steel substrates. Surf. Eng. 22, 26–34 (2006). https://doi.org/10.1179/174329406X84949CrossRef

Titel: Co-based and Co/WC Laser Metal Deposition: A Comparative Study between Continuous and Pulsed Wave Laser Process Conditions
verfasst von: Haideé Ruiz-Luna
Cinthia Estefania Cuevas-Mercado
Christian Félix-Martínez
Juan Manuel González-Carmona
Juan Ruiz-Ornelas
Juan Manuel Alvarado-Orozco
Publikationsdatum: 25.04.2024
Verlag: Springer US
Erschienen in: Lasers in Manufacturing and Materials Processing / Ausgabe 2/2024
Print ISSN: 2196-7229
Elektronische ISSN: 2196-7237
DOI: https://doi.org/10.1007/s40516-024-00255-8

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 2/2024

An Experimental Investigation on the Laser Forming of Aluminum/Epoxy/Glass FMLs

Experimental Investigation on the Effect of Nickel-plating Thickness on Continuous-wave Laser Welding of Copper and Steel Tab Joints for Battery Manufacturing

Evaluating the Effect of Deposition Strategy on Mechanical Characteristics of 316L Parts Produced by Laser Powder Directed Energy Deposition Process

CO2 Laser Sintering of TiO2 Nanoparticles Thin Films for Improved Transmittance

Effect of Process Parameters on Melt Pool Characteristics and Solidification Process During Laser Powder Bed Fusion of AlSi10Mg Alloy

Experimental and Statistical Study on Mechanical Behavior of H13 Tool Steel Additively Manufactured and Laser Surface Treated

Premium Partner

Marktübersichten