nach oben

Physics of Metals and Metallography

Erschienen in:

29.12.2023 | STRENGTH AND PLASTICITY

Research on the Choice of Cooling Method for a Rare-Earth Wrought Magnesium Alloy Considering Temperature Distribution, Hardness and Microstructure

verfasst von: Qiumin Xie, Yunxin Wu, Yuanzhi Wu, Shunli Peng, Zhongyu Yuan

Erschienen in: Physics of Metals and Metallography | Ausgabe 13/2023

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

A “hardenability” experiment which contained solution treatment followed by single-side quenching and aging afterward of a cylinder specimen was carried out to research on the choice of cooling method considering temperature distribution, hardness and microstructure for a newly developed high-strength heat resistant rare-earth wrought magnesium alloy Mg–Gd–Y–Zr–Ag–Er. The results revealed that the closer the sample was to the quenching surface, the faster the temperature decreased. The largest measured temperature difference was 320°C. The hardness was ranging from 76 to 86 HV in the quenched state, and 110 to 119 HV in the aged state. The various cooling rates had little effect on the hardness, the grains and precipitates of this kind of magnesium alloy, solution treatment followed by a lower cooling process like air cooling may be a better choice.

Vorheriger Artikel Microstructural Evolution and Mechanical Behavior of SP-700Ti Alloy during Superplastic Deformation

Nächster Artikel The Influence of Nickel Addition on Properties of Sn–4.0Zn–0.7Cu Lead-Free Solder

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Wirtschaft"

Online-Abonnement

Mit Springer Professional "Wirtschaft" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 340 Zeitschriften

aus folgenden Fachgebieten:

Bauwesen + Immobilien
Business IT + Informatik
Finance + Banking
Management + Führung
Marketing + Vertrieb
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

H. Wang and T. Wang, “Influence of hot rolling and solution treatment on the microstructure and mechanical properties of high-boron duplex stainless steel 0Cr21Ni5Ti–2B,” Met. Sci. Heat Treat. 63, 126–131 (2021). https://doi.org/10.1007/s11041-021-00658-wCrossRef

Z. Li, H. Wang, Yu. Zhao, L. Wu, F. Zhang, and Q. Shan, “Effect of progressive solid-solution treatment on microstructures, mechanical properties and impact abrasive wear behavior of alloyed high manganese steel,” Mater. Res. Express 9, 036512 (2022). https://doi.org/10.1088/2053-1591/ac5cadADSCrossRef

Yi. Sun, F. Jiang, H. Zhang, J. Su, and W. Yuan, “Residual stress relief in Al–Zn–Mg–Cu alloy by a new multistage interrupted artificial aging treatment,” Mater. Des. 92, 281–287 (2016). https://doi.org/10.1016/j.matdes.2015.12.004CrossRef

J.-S. Wang, Ch.-Ch. Hsieh, H.-H. Lai, Ch.-W. Kuo, P. T.-Yu. Wu, and W. Wu, “The relationships between residual stress relaxation and texture development in AZ31 Mg alloys via the vibratory stress relief technique,” Mater. Charact. 99, 248–253 (2015). https://doi.org/10.1016/j.matchar.2014.09.019CrossRef

H. Zengin, Yu. Turen, M. E. Turan, and F. Aydın, “Evolution of microstructure, residual stress, and tensile properties of Mg–Zn–Y–La–Zr magnesium alloy processed by extrusion,” Acta Metall. Sin. (Engl. Lett.) 32, 1309–1319 (2019). https://doi.org/10.1007/s40195-019-00901-7

K. Asl, A. Tari, and F. Khomamizadeh, “Effect of deep cryogenic treatment on microstructure, creep and wear behaviors of AZ91 magnesium alloy,” Mater. Sci. Eng., A 523, 27–31 (2009). https://doi.org/10.1016/j.msea.2009.06.003CrossRef

D. Han, H. Chen, Q. Zang, Yu. Qian, H. Cui, L. Wang, J. Zhang, and Yu. Jin, “Effect of solution treatment on microstructure and properties of Mg–6Gd–3Y–1.5Zn–0.6Zr alloy,” Mater. Charact. 163, 110295 (2020). https://doi.org/10.1016/j.matchar.2020.110295CrossRef

J. Iwaszko and K. Kudła, “Microstructure, hardness, and wear resistance of AZ91 magnesium alloy produced by friction stir processing with air-cooling,” Int. J. Adv. Manuf. Technol. 116, 1309–1323 (2021). https://doi.org/10.1007/s00170-021-07474-9CrossRef

C. Wang, T. Luo, Yu. Liu, Q. Huang, and Yu. Yang, “Residual stress and precipitation of Mg–5Zn–3.5Sn–1Mn–0.5Ca–0.5Cu alloy with different quenching rates,” J. Magnesium Alloys 9, 604–612 (2021). https://doi.org/10.1016/j.jma.2020.02.021CrossRef

10.

Q. Xie, Yu. Wu, T. Zhang, S. Peng, and Z. Yuan, “Effects of quenching cooling rate on residual stress and mechanical properties of a rare-earth wrought magnesium alloy,” Materials 15, 5627 (2022). https://doi.org/10.3390/ma15165627ADSCrossRefPubMedPubMedCentral

11.

C. Wang, T. Luo, J. Zhou, and Yu. Yang, “Effects of solution and quenching treatment on the residual stress in extruded ZK60 magnesium alloy,” Mater. Sci. Eng., A 722, 14–19 (2018). https://doi.org/10.1016/j.msea.2018.02.047CrossRef

12.

D. Wang, P. Fu, L. Peng, Yi. Wang, and W. Ding, “Quench sensitivity characterization of a LPSO-phase containing Mg alloy,” Mater. Sci. Eng., A 749, 291–300 (2019). https://doi.org/10.1016/j.msea.2019.02.011CrossRef

13.

J.-F. Li, D.-Ya. Liu, H. Ning, C. Liu, P.-Ch. Ma, Yo.‑L. Chen, and X.-H. Zhang, “Experimental quantification of “hardenability” of 2195 and 2050 Al–Li alloys by using cold-rolled sheets,” Mater. Charact. 137, 180–188 (2018). https://doi.org/10.1016/j.matchar.2018.01.037CrossRef

14.

J. Yan, Q.-L. Pan, A.-D. Li, and W.-B. Song, “Flow behavior of Al–6.2Zn–0.70Mg–0.30Mn–0.17Zr alloy during hot compressive deformation based on Arrhenius and ANN models,” Trans. Nonferrous Met. Soc. China 27, 638–647 (2017). https://doi.org/10.1016/s1003-6326(17)60071-2CrossRef

15.

Yu-X. Zhang, Yo.-P. Yi, Sh.-Q. Huang, and F. Dong, “Influence of quenching cooling rate on residual stress and tensile properties of 2A14 aluminum alloy forgings,” Mater. Sci. Eng., A 674, 658–665 (2016). https://doi.org/10.1016/j.msea.2016.08.017CrossRef

16.

L. Xiao, G. Yang, H. Qin, J. Ma, and W. Jie, “Microstructure evolution and quench sensitivity characterizations of Mg–9.5Gd–0.9Zn–0.5Zr alloy,” Vacuum 181, 109651 (2020). https://doi.org/10.1016/j.vacuum.2020.109651ADSCrossRef

17.

H.-Yi. Li, C.-T. Zeng, M.-Sh. Han, J.-J. Liu, and X.‑Ch. Lu, “Time–temperature–property curves for quench sensitivity of 6063 aluminum alloy,” Trans. Nonferrous Met. Soc. China 23, 38–45 (2013). https://doi.org/10.1016/s1003-6326(13)62426-7CrossRef

18.

J. S. Robinson, P. J. Tiernan, and J. F. Kelleher, “Effect of post-quench delay on stress relieving by cold compression for the aluminium alloy 7050,” Mater. Sci. Technol. 31, 409–417 (2015). https://doi.org/10.1179/1743284714y.0000000571ADSCrossRef

19.

J. Liu, F. Jiang, M. Tang, B. Liu, Yi. Sun, and H. Zhang, “Reduced residual stress and retained properties in Al–Zn–Mg–Cu alloys using a novel cladding quenching process,” J. Mater. Res. Technol. 9, 7201–7209 (2020). https://doi.org/10.1016/j.jmrt.2020.04.080CrossRef

20.

X. Geng, Z. Cheng, S. Wang, C. Peng, A. Ullah, H. Wang, and G. Wu, “A data-driven machine learning approach to predict the hardenability curve of boron steels and assist alloy design,” J. Mater. Sci. 57, 10755–10768 (2022). https://doi.org/10.1007/s10853-022-07132-9ADSCrossRef

21.

B. Wang, Yo. Gao, and C. Liu, “Effect of multidirectional forging and ageing treatment on microstructure and mechanical properties of Mg–Gd–Y–Zr alloy,” Ordnance Mater. Sci. Eng. 41, 27–31 (2018).CrossRef

22.

J.-F. Nie, “Precipitation and hardening in magnesium alloys,” Metall. Mater. Trans. A 43, 3891–3939 (2012). https://doi.org/10.1007/s11661-012-1217-2CrossRef

23.

Yi. Huang, C. Liu, S. Jiang, Ya. Ma, Yi. Wan, and Z. Chen, “Dislocation-induced β' precipitation behavior and strength-ductility synergistic enhancement in Mg–Gd–Y–Zr–Ag alloy,” J. Alloys Compd. 944, 169187 (2023). https://doi.org/10.1016/j.jallcom.2023.169187CrossRef

24.

Yi. Huang, C. Liu, Yi. Wan, S. Jiang, Yo. Gao, and Z. Chen, “Effect of dislocation-induced aging precipitate bands on creep resistance of Mg–Gd–Y–Zr–Ag alloy,” J. Alloys Compd. 960, 170633 (2023). https://doi.org/10.1016/j.jallcom.2023.170633CrossRef

25.

L. Wang, J. Huang, Yo. Peng, and Yi. Wu, “Precipitates evolution in the heat affected zone of Mg–Gd–Y–Zr alloy in T6 condition during laser welding,” Mater. Charact. 154, 386–394 (2019). https://doi.org/10.1016/j.matchar.2019.06.004CrossRef

Titel: Research on the Choice of Cooling Method for a Rare-Earth Wrought Magnesium Alloy Considering Temperature Distribution, Hardness and Microstructure
verfasst von: Qiumin Xie
Yunxin Wu
Yuanzhi Wu
Shunli Peng
Zhongyu Yuan
Publikationsdatum: 29.12.2023
Verlag: Pleiades Publishing
Erschienen in: Physics of Metals and Metallography / Ausgabe 13/2023
Print ISSN: 0031-918X
Elektronische ISSN: 1555-6190
DOI: https://doi.org/10.1134/S0031918X23600033

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Wirtschaft"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 13/2023

Study on the Micro-Texture and Anisotropy of a Cold-Rolled and Intercritically Annealed DP800 Steel

Effect of Nb Doping on Thermoelectric Properties of TiNiSn Half-Heusler Alloy Prepared by Microwave Method

Wear Performances of Hypereutectoid P/M Steels Subjected to Different Heat Treatments

Hierarchical Heterogeneity in Bulk Metallic Glasses Rejuvenated by Cryogenic Thermal Cycling

Effect of Platinum Addition on Microstructure and Oxidation Behavior of Ni3Al-Base Alloys

Rate-Dependent Compressive Behaviour of SiC−B4C−Al Hybrid Composites